Garage doors that are automated and have automatic remotes are fantastic features that make life easier. Who would want to get out of their car, explore the weather, and struggle with an open door that is manual? However, there’s a second category of people who prefer the ease of accessing a home garage.
Yes, you’re right. We’re talking about burglars. They’re known to gain access to homes via the garage. Therefore, taking measures to change the programming of your opener on a regular basis will help to stop them. Also, you wouldn’t want your door to open whenever a neighbor is using their opener, right?
Hackers
Burglars are using a new method to gain access into your home and hack your home. Yes, even criminals are always on the lookout for the latest technology. Hacking wireless devices is an extremely low-cost technology. It’s not that big of a financial investment from an experienced burglar.
Hacking process: By pressing your garage door opener’s button, it transmits the signal using unsafe wireless technology to the garage door’s remote. It takes only a few minutes for thieves to get that signal. Once they’ve got that information, they are able to duplicate it at any time.
A burglar can observe your house and track your movements and activities, and gain entry into your garage when you’re not there. If your car has been taken, now the criminal has access to the garage too. In the event that one of your remotes are absent, it’s time to reset the rest of them.
When is the right time to reprogram my garage door opener?
Reprogramming your garage door remote will ensure you a safer home. Most people have lost tracks of their garage door remotes, they are either lost, stolen, or given to neighbors. It happens. If one remote is missing, you should reset all the remotes.
Even if all of your remotes are in order, you should set a scheduled time frame for reprogramming. Maybe you have a security system for your home. If you program it remote, you can do it the next day.
Start Over
Sometimes, it’s also essential to erase all old codes off the device. For instance, when you move to a new house however the previous owner removed the remote from their home. As we’ve discussed in the past, a myriad of factors can cause your garage door to swing open completely by itself.
Even if all of your remote controls are properly programmed, choose a scheduled interval to reprogram. Maybe you are using a home security system. If you change the program remote, you can do it at the same time. Also, make sure to check the remote while you replace the batteries inside the smoke detector.
Garage Door Opener Reprogramming is Not Difficult
It’s a fairly simple job, so you should make sure you do it before thieves get an opportunity to target you. It’s not a guarantee however, a fresh code can deter thieves and provide peace of assurance. Follow these steps to reprogram the opener as well as the remote.
On the garage door opener remove the small plate, revealing the panel that controls it. Find the button for learning after which push and release the learn button. This is a very popular LiftMaster model in this case. If you’re using other brands and models, it is possible to take off the entire cover. However, most openers offer an easy access to the panel.
With the remote in your pocket, press to release your opener button. The light will turn on after 30 seconds. Once it’s glowing, you need to push and hold down the remote button until you’re able to see the lights flash in the device. If the unit isn’t equipped with lights, then press the button for program (or the red learn button) and hold the remote’s button until you get two clicking sounds.
In essence, you’re sending the number through your device to that allows it to recognize your remote whenever you want to use it again next time. It’s similar to changing your debit card’s pin, but you don’t need to think of it all the time.
If you want to delete all the codes from the unit’s memory, long press the program’s “learn” button until the light turns on, and it goes out. It typically takes five to six seconds, and all the codes will be erased. Then, you can follow the steps aforementioned to program the unit and remote.
Contact a Professional
If your remote isn’t opening your garage, and these solutions aren’t working, do not hesitate to call Direct Service Overhead Garage Door Company for help. Garage door openers are an integral part of the security system of your home, and it must be considered as it is. The company we work with has been business for quite a while and have experienced everything.
0 Comments